Liste der Anhänge anzeigen (Anzahl: 2)
Neuerwerbung Europlay Bildstörung Hantarex MTC 9000
Hallo,
wie schon im Vorstellungsthread angekündigt, habe ich ein Problem mit meiner Neuerwerbung.
Der Monitor zeigt nichts brauchbares an.
Da ich mich nicht mit Monitoren und der genauen Fehlerbezeichnung auskenne, bleibt nur noch
ein Video und die Bilder.
Ich hoffe, Ihr könnt mir sagen, wie der Fehler heisst und am Besten noch,
was ich dagegen tun kann :confused:
Vielen Dank im voraus!
LG
Jürgen
Link zum Video
Liste der Anhänge anzeigen (Anzahl: 1)
anbei noch ein screenshot vom Video, Sieht aber besser aus, wie im Video selbst.
Liste der Anhänge anzeigen (Anzahl: 1)
Den Wackelkontakt im Netzteil habe ich gefunden: ein Zementwiderstand mit zwei kalten Lötstellen. Jetzt lässt sich der Automat wenigstens zuverlässig einschalten.
Das Monitorproblem ist leider immer noch nicht gelöst.
Video Sync und Video Ground von der Spieleplatine bis zum Chassis durchgemessen und o.k.
Das Chassis ist doch die grosse Platine auf der linken Seite (siehe Bild)
Die kann ich nicht ausbauen, ohne den Monitor zu entladen, oder hab ich das falsch verstanden?
Bitte um Hilfe, ich bin mit sowas noch auf Anfängerniveau :confused:
LG
Jürgen
Liste der Anhänge anzeigen (Anzahl: 1)
ich habe hier (klick mich, ich bin ein PDF-link) noch was gefunden.
Das hört sich eigentlich genau nach meinem Problem an.
Die Frage ist nur, was und wo ist P9 und was soll das Umschalten bringen?
Siehe Bild unten.
Anhang 12883
Liste der Anhänge anzeigen (Anzahl: 1)
Was ich ganz vergessen hatte...das ist ein Hantarex Chassis MTC9110. Auf dem Neckboard steht zwar 9000, aber die sind nur für Bildschirmgrößen bis 21". Das 9110 geht bis 28". Leicht zu erkennen am Lüfter über dem Zeilentrafo. Irgendwo klebt auch ein grüner Aufkleber, auf dem 9110 steht, falls er über die Jahre noch nicht abgefallen ist. Aber egal.
Der Schalter P9 ist wahrscheinlich der kleine Schiebeschalter (eigentlich SW4, P9 ist meines Erachtens nur eine Drahtbrücke), mit dem man das Sync-Signal umschalten kann....zwischen positiv und negativ, wenn ich mich nicht irre. Position siehe Bild. Ich glaube nicht, dass es daran liegt, aber ein Versuch ist es sicher mal wert.
Haste den Winni schon angeschrieben? Klar, wird er sich darum kümmern, aber das macht er nicht kostenlos!! (keine Angst, Winni hat vernünftige Preise ;) )
Anhang 12884
Liste der Anhänge anzeigen (Anzahl: 1)
Zitat:
Zitat von
Luigi
Hi Luigi,
danke, ich hab das Bild ganz übersehen :o . Genau das war der Schalter und genau falsch gestellt im Vergleich zu der Stellung auf Deinem Bild.
Danke nochmals.
Noch ne letzte Frage hätte ich. Hab ich das richtig eingesteckt? (siehe Bild).
Anhang 12885
Und ja, da gibts doch noch was zu putzen :D
LG
Jürgen